VIRANIX 2K PRO
Looking for a water-permeable surface that feels more slip-resistant?2K PRO is that kind of system.
A two-component, aliphatic polyurethane binder with natural crushed marble aggregate. For both foot and vehicle traffic. For terraces, pool surrounds, garden paths and driveways.
On glazed floor tiles or sealed concrete, water has nowhere to go. It stays on the surface — and that is most unpleasant exactly where people walk barefoot.
VIRANIX 2K PRO creates an open-pored surface. Pores remain between the marble pebbles, so once applied, water does not collect on the surface. The texture of the walking surface comes from the stone itself.
The color comes from natural marble, not from pigment — which is why slight shade variations between production batches are possible.
Three products make up the system
Primer, aggregate and binder. The aggregate and binder are mixed on site, then spread and compacted with a stainless steel trowel. The binder is solvent-free.
The same material for foot and vehicle traffic. Both grain sizes — 2–4 mm and 3–5 mm — are suitable for surfaces with foot traffic as well as vehicle traffic. The minimum layer thickness is 8 mm in both cases.
Aliphatic formulation with high UV resistance. The binder is based on aliphatic polyurethane — a formulation developed specifically for outdoor use.
Seamless, continuous surface. No joints and no tile edges within the surface.
Chemical-resistant. Resistant to water and most chemicals, as well as to staining caused by atmospheric pollution.
Currently available in 2–4 mm and 3–5 mm grain sizes, in six colors.
Water permeability does not replace waterproofing
On the 2K PRO surface, water does not collect — it passes through the open pore structure. But from there it travels on, underneath the surfacing.
That is why proper falls and drainage are part of the system. If there is a living space, garage or basement below the surfacing, the waterproofing goes under the stone carpet, not instead of it. This has to be decided at the planning stage — afterwards it can only be fixed by demolition.
2K PRO or the factory pre-mixed 1K?
We have two stone carpet systems, and the choice comes down to a single question: should the surface be closed or open? Sealed with a PRIMECOAT 2K topcoat, the factory pre-mixed 1K forms a closed, easy-to-clean surface, but it does not replace waterproofing. 2K PRO stays open-pored and lets water through. They are separate systems, so we never mix them within one surface.
VIRANIX stone carpet
1K · factory pre-mixed · water-based
- Factory pre-mixed: no dosing of components — simply stir thoroughly before use
- Solvent-free, low-odor — suitable indoors too
- Must always be sealed with a topcoat: PRIMECOAT 2K, or PRIMECOAT 2K PRO for vehicle traffic
- Closed, easy-to-clean surface with PRIMECOAT 2K sealing (does not replace waterproofing)
- Also for walls and plinths: 2–4 mm, with fine grain
- Fine grain only for foot traffic and decorative use; medium grain for vehicle traffic
VIRANIX 2K PRO
2K · aliphatic PU · mixed on site
- Aggregate and binder supplied separately, mixed in a set ratio
- Open-pored, water-permeable surface
- Aliphatic formulation with high UV resistance
- Min. layer thickness 8 mm
- Both grain sizes can be used up to vehicle traffic
- Dedicated PU primers — and VAPOGRIP EP 2K where ground moisture is suspected
The substrate makes or breaks the job
Stone carpet is only as good as the concrete beneath it. Applied to a moving, cracking substrate, the surfacing will crack exactly where the substrate does. Stone carpet is not a crack filler.
Suitable substrates
Concrete, screed, industrial floors — in a stable, load-bearing, crack-free condition. Stable ceramic tiling too, with mechanical preparation. In new buildings, according to the primer's data sheet, a drying time of at least 28 days is required, and the moisture content must not exceed 5%.
A common mistake: never wash the substrate with water before priming. Mechanical cleaning is fine — wet cleaning is not.
Damp substrates and ground moisture
Primer selection depends on the substrate. For dry substrates, use the single-component 2K PRO PU Primer. Where ground moisture or a damp, moisture-affected substrate is suspected, the water-based epoxy primer VAPOGRIP EP 2K goes under the 2K PRO stone carpet instead of a PU primer. The two-component 2K PRO PU Primer (2K) is the fast-curing PU primer of the system. A single-component primer does not provide reliable adhesion on damp concrete.
What needs dealing with first
Cracked, moving or settling substrate — structural repair first. Dusting, crumbling surface — grinding, followed by a penetrating primer. Oily, greasy concrete, which is typical in garages — without degreasing and grinding, adhesion will not be adequate.
And one thing worth clarifying at the survey stage: substrates in contact with the ground. If there is no vapor barrier below, ground moisture can break down the bond from underneath — in this case, use VAPOGRIP EP 2K as the primer.
The 2K PRO PU Primer penetrates the pores and strengthens the substrate from within — that is the difference between a surface primer and a penetrating primer. Consumption 150–200 g/m².
The layer build-up, step by step
1. Preparation. Grinding, dust removal with an industrial vacuum cleaner, degreasing, crack repair and leveling if necessary. Fix the edge protection profiles at this stage — after priming they can no longer be fitted cleanly.
2. Priming. The primer matching the condition of the substrate (2K PRO PU Primer, or VAPOGRIP EP 2K where ground moisture is suspected), applied by roller or brush with full coverage; 2K PRO PU Primer at 150–200 g/m². On large areas, airless spraying can also be used. Application temperature +5…+30/35 °C. Touch-dry in 6–8 hours at 20 °C; the overcoating window is 2–3 hours, 4 hours at the latest.
3. Mixing. For both 2–4 mm and 3–5 mm grain, 1.5 kg of binder goes with 25 kg of aggregate. With the two-component binder, both the ratio and the thoroughness of mixing matter — the exact mixing instructions are given in the product data sheet.
4. Spreading and compacting. With a stainless steel trowel, using even pressure. Minimum layer thickness 8 mm — depending on compaction, this can increase by 10–15%, and the material requirement increases accordingly.
5. Cleaning tools. Immediately after work. Once cured, the binder is difficult to remove from the trowel and the mixing paddle.
The binder comes as component A and component B — in a 1.5 kg set and in a 14 kg (8+6 kg) pack.
Installation details
Decide on section boundaries before you start. Door lines, changes of floor covering, profiles, corners. That way you never have to cross a freshly laid surface.
Mix only as much as you can work in. The pot life of the two-component material is limited (approx. 45–50 minutes). If a zone is left half-finished, the joint will be visible in the finished surface.
Compacting is part of spreading. Work with even pressure: pulling too hard displaces the grains, too little pressure leaves a loose surface. Finish details — along profiles, at doors — with a smaller trowel.
Expansion joints: tape, not sealant. Wherever there is an expansion joint in the substrate, there must be one in the surfacing too. Use DILITAPE expansion joint tape for this. At wall–floor junctions use SEALBAND FLEX, and ARMURNET glass-fiber mesh to prevent cracks from transferring.
Plan for more on complex surfaces. Stairs, many corners, columns — both the material requirement and the time increase.
Pack sizes and prices
VIRANIX 2K PRO system
VIRANIX stone carpet — factory pre-mixed 1K
Prices include 27% Hungarian VAT and may change without prior notice. Current prices and stock levels are shown in the webshop.
How much material do you need for a 20 m² terrace?
2–4 mm grain, 2K PRO system, level and dry concrete substrate. Calculated with net consumption, without allowance for waste.
This is material cost only. Substrate preparation and installation labor are assessed separately by the installer, based on the condition of the surface.
Delivery: home delivery 24,990 HUF, or free personal pickup in Dunaharaszti.
If the substrate is the problem: waterproofing and structural repair
Stone carpet is a decorative surfacing. If water is leaking in under the terrace, or the concrete is already cracked and crumbling, two jobs come before the surfacing. We have a dedicated product family for each.
AQUASHIELD PUR UV-1K — forms a continuous, flexible membrane once cured.
If waterproofing goes under the surfacing
A cured, flexible waterproofing membrane is not a suitable base for stone carpet on its own. Mechanical anchoring is needed between the two: coarse quartz or corundum grit must be broadcast into the still-wet membrane.
Without it, the stone carpet has nothing to grip.
VIRANIX REPAIR 800 R4 — for structural concrete repair, class R4 according to EN 1504-3.
Which system is right for your surface?
We need to know three things: how large the area is, what is on it now, and what it will be used for — foot traffic, vehicles or a pool surround. From that, we can give you the material requirement and a price.
VIRANIX 2K PRO products+36 70 575 5500
VIRANIX Hungary Kft. · 2330 Dunaharaszti, Némedi út 65. · Showroom Mon–Fri 10:00–16:00





Share:
Installing VIRANIX 1K Stone Carpet Step by Step: Spreading, Compacting and the Most Common Mistakes